Vaisala DRYCAP DMT143 Uživatelská příručka Strana 40
- Strana / 76
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
USER'S GUIDE ____________________________________________________________________
38 ___________________________________________________________________ M211435EN-E
List of Serial Commands
All commands can be issued either in uppercase or lowercase. In the
command examples, the keyboard input by the user is in bold type.
The notation <cr> refers to pressing the carriage return (Enter) key on
your computer keyboard. Enter a <cr> to clear the command buffer
before starting to enter commands.
Table 7 List of Serial Commands
Command
Description
<ESC>
Stop the continuous outputting of RUN mode
or R command
?
Show device information
??
Show device information (overrides poll mode)
ADDR [0 … 255]
Show or set transmitter address
AERR
Set analog output error level
ALARM
Set dewpoint level for LED alarm
AMODE
Show analog output mode
AOUT [ON/OFF]
Enable or disable analog output
AOVER [ON/OFF]
Allow analog outputs to exceed their range 10%
ASEL
Set analog output parameter and scaling
ATEST
Test analog output
CLOSE
Close the temporary connection and return the
device to POLL mode
ERRS
Display the currently active errors
FILT [0 ... 1]
Set output filtering level
FORM [modifier string]
Set output format
FRESTORE
Restore factory settings
GAS [0 ... 1]
Set measured gas type
HELP
Show list of currently available serial commands
INTV [0 ... 255 S/MIN/H]
Set the continuous output interval
(for RUN mode and R command)
L
Show user adjustment values
LI
Set user adjustment values
OPEN [0 … 255]
Open a line to transmitter at defined address
PRES [0.001 ... 50]
Set permanent pressure compensation value
R
Start the continuous outputting
RESET
Reset the transmitter
SDELAY [0 … 255]
Set response sending delay
SEND [0 … 255]
Output readings once
(specify address for transmitters in POLL mode)
SERI [baud p d s]
Show or set the serial interface settings
SMODE [mode]
Show or set startup serial mode:
RUN, STOP, or POLL
SNUM
Display transmitter serial number
SYSTEM
Show transmitter firmware information
TIME
Show transmitter uptime
UNIT [m/n]
Select metric or non-metric units
VERS
Show transmitter firmware version
XPRES [0.001 ... 50]
Set temporary pressure compensation value
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 6 5
- CHAPTER 7 5
- CHAPTER 8 5
- List of Figures 6
- List of Tables 6
- GENERAL INFORMATION 7
- Version Information 8
- Related Manuals 8
- Documentation Conventions 8
- Recycling 9
- Regulatory Compliances 10
- Trademarks 10
- License Agreement 10
- Warranty 10
- PRODUCT OVERVIEW 11
- Basic Features and Options 12
- Transmitter Parts 13
- Model with NPT Thread 14
- Loop-Powered Display 15
- Connection Cables 16
- Sampling Accessories 16
- FUNCTIONAL DESCRIPTION 17
- Sensor Purge 18
- Freezing Conditions 18
- DMT143 Startup Sequence 19
- Alarm LED 20
- INSTALLATION 21
- Selecting the Location 22
- Installing the Transmitter 22
- 1202-123 23
- 1202-124 23
- Power Supply Requirements 25
- 1203-129 26
- Sampling from a Process 28
- Connector and Leak Screw 29
- 0507-105 30
- 0510-034 32
- 1202-125 34
- 1203-051, 1203-052 36
- 0807-004 39
- List of Serial Commands 40
- Device Information 41
- Show Firmware Version 42
- Show Firmware Information 42
- Show Currently Active Errors 42
- Show Serial Number 42
- Show Command List 43
- Configuring Analog Output 44
- Extend Analog Output Range 46
- Test Analog Output 46
- Serial Line Output Commands 47
- Set Output Interval 48
- Output a Reading Once 48
- Set Measured Gas Type 51
- Set Measurement Filtering 51
- Select Unit 53
- CAUTION 54
- Set Serial Line Settings 55
- Set Transmitter Address 56
- Other Commands 57
- Configure the Alarm LED 58
- Show Transmitter Uptime 59
- Reset Transmitter 59
- Restore Factory Settings 59
- MAINTENANCE 61
- Changing the Filter 62
- Dewpoint Meter 63
- 1108-039 64
- TROUBLESHOOTING 67
- Error Messages 68
- Unknown Serial Settings 68
- Technical Support 69
- Product Returns 69
- TECHNICAL DATA 71
- Dewpoint temperature (°C) 72
- Table 17 General 73
- Spare Parts and Accessories 74
- NPT1/2" 75
- *M211435EN* 76
Související produkty a manuály pro Měření, testování a kontrola Vaisala DRYCAP DMT143
(10 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce