Vaisala PTU300 Uživatelská příručka Strana 131
- Strana / 173
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6 ___________________________________________________Calibration and adjustment
VAISALA ______________________________________________________________________ 129
LC
Use the command LC to view current status of the linear offset and
offset/gain pressure corrections.
Example:
>lc
P1 linear adj. : ON
P1 1.reading : 950.000
P1 1.correction: 0.220
P1 2.reading : 1120.000
P1 2.correction: 0.150
MPCI
Use the command MPCI
- to activate or deactivate multipoint adjustment function
- to enter new multipoint corrections to the transmitter
- to edit existing multipoint corrections.
First deactivate the previous corrections by using the LCI OFF and/or
MPC1 OFF commands. Precalibration of the transmitter then gives the
required corrections.
When entering new multipoint corrections, always start at the low-
pressure end and then go up the pressure range. Key in the multipoint
corrections for each pressure transducer separately.
NOTE
The new multipoint corrections will always cancel the previous
corrections as well as the valid date of calibration of the transmitter.
Example:
>mpci
P1 multi adj. : OFF ? on
P1 1.reading : 0.000 ? 900
P1 1.correction: 0.000 ? 0.2
P1 2.reading : 0.000 ? 950
P1 2.correction: 0.000 ? 0.22
P1 3.reading : 0.000 ? 1000
P1 3.correction: 0.000 ? 0.27
P1 4.reading : 0.000 ? 1050
P1 4.correction: 0.000 ? 0.31
P1 5.reading : 0.000 ? 1100
P1 5.correction: 0.000 ? 0.32
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 5 6
- CHAPTER 6 6
- List of Figures 8
- List of Tables 9
- GENERAL INFORMATION 11
- Feedback 12
- ESD Protection 12
- Recycling 13
- Regulatory Compliances 13
- Trademarks 13
- License Agreement 13
- Warranty 14
- PRODUCT OVERVIEW 15
- Basic Features and Options 16
- Pressure Measurement 17
- 0601-008 18
- Probe Options 20
- Warmed Probe PTU307 21
- INSTALLATION 23
- Standard Mounting without 24
- Mounting Plate 24
- 0503-004 25
- 0503-040 25
- Kit for Pole or Pipeline 27
- 0503-041 28
- 0509-151 28
- Cable Bushings 30
- Grounding the Cables 31
- Alternate Wiring Systems 33
- WARNING 34
- 8-Pin Connector 35
- D-9 Connector 36
- CAUTION 37
- Probe Mounting 38
- 0507-024 39
- 0507-022 40
- Temperature Probe (Optional) 42
- Power Supply Module 43
- Installation 44
- Warnings 44
- 0506-030 47
- Relays 49
- RS-422/485 Interface 51
- 1 (not connected) RxB 52
- 2 (not connected) RxA 52
- 4 B TxB 52
- 5 A TxA 52
- OPERATION 55
- Basic Display 56
- Reading 57
- 0604-055 58
- Graphic History 60
- Information Display 61
- Menus and Navigation 62
- Language Setting 63
- Rounding Setting 63
- Display Backlight Setting 63
- Display Contrast Setting 64
- Keypad Lock (Keyguard) 64
- Menu PIN Lock 64
- Factory Settings 65
- Serial Line Communication 66
- User Port Connection 66
- Service Port Connection 67
- Terminal Program Settings 68
- 0601-029 69
- 0601-030 69
- List of Serial Commands 70
- Getting Measurement Message 73
- Setting time and date 75
- General Settings 75
- NMEA Data Format 79
- GPS Commands 81
- User Port Serial Settings 85
- Pressure Average Calculation 88
- Device Information 89
- Serial Line 92
- Locking Menu/Keypad by Using 92
- Data Recording 93
- Selecting Data Recording 93
- Quantities 93
- View Recorded Data 94
- Deleting the Recorded Files 96
- Analog Output Settings 96
- 0503-045 97
- AMODE/ASEL 99
- Analog Output Tests 100
- Setting 101
- Operation of Relays 102
- Quantity For Relay Output 102
- Hysteresis 103
- Enabling/Disabling Relays 105
- Setting Relay Outputs 106
- Testing Operation Of Relays 108
- Operation of RS-485 Module 109
- Networking Commands 110
- Sensor Functions 113
- Chemical Purge (Optional) 113
- Manual Chemical Purge 114
- Chemical Purge in Power Up 115
- Using Buttons On Motherboard 115
- Using Serial Line 116
- Setting Sensor Heating 117
- MAINTENANCE 121
- Changing the Sensor 122
- Error States 123
- Table 18 Error Messages 124
- CALIBRATION AND ADJUSTMENT 127
- 0508-013 128
- Relative Humidity Adjustment 132
- Using Push-Buttons 132
- Using Display/Keypad 133
- Temperature Adjustment 137
- TECHNICAL DATA 143
- Relative Humidity 144
- Optional Temperature Probe 145
- Calculated Variables 146
- 1013 mbar) 147
- Dewpoint Temperature (PTU307 148
- Warmed Probe Option) 148
- Inputs and Outputs 149
- Mechanics 149
- Technical Specifications of 150
- Optional Modules 150
- Relay Module 151
- RS-485 Module 151
- Options and Accessories 151
- Item code 152
- Dimensions (in mm and inch) 153
- 12 (0.47) 154
- 120 (4.72) 154
- Temperature Probe 155
- Technical Support 155
- Return Instructions 156
- Vaisala Service Centers 157
- PROBE INSTALLATION KITS AND 159
- INSTALLATION EXAMPLES 159
- PTU307) 160
- RH Probe Installation 161
- 0508-016 162
- 0508-018 164
- 0508-015 164
- 0507-015 167
- 0601-044 168
- CALCULATION FORMULAS 169
Související produkty a manuály pro Měření, testování a kontrola Vaisala PTU300
(221 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce