Vaisala PTU300 Uživatelská příručka Strana 132
- Strana / 186
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
USER'S GUIDE____________________________________________________________________
130 _________________________________________________________________ M210796EN-E
0508-035
Figure 62 Decrease of Sensor Gain
Before starting the chemical purge note the following:
- the sensor is protected with a PPS grid with stainless steel netting, a
stainless steel sintered filter or with membrane SST filter
- the sensor temperature must be below 100 °C. At higher temperatures
the chemicals evaporate spontaneously from the sensor and the
chemical purge is not necessary.
Automatic Chemical Purge (Interval Purge)
When PTU300 leaves the factory the automatic chemical purge (if
chosen) takes place repeatedly with the time intervals set in the factory.
User can change the interval in which the purge takes place by using
serial commands or with the optional display/keypad. This can be needed
if the measuring environment contains high concentrations of interfering
chemicals. The automatic chemical purge can also be turned off if
necessary.
Manual Chemical Purge
The chemical purge should be performed always before calibration (see
section Calibration and adjustment on page 141) or when there is a
reason to believe that a sensor has become exposed to an interfering
chemical. Make sure that the temperature of the sensor has come down to
normal temperature before starting a calibration.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 4 4
- CHAPTER 5 7
- CHAPTER 6 7
- CHAPTER 7 8
- APPENDIX A 8
- APPENDIX B 9
- List of Figures 10
- List of Tables 12
- GENERAL INFORMATION 13
- Feedback 14
- ESD Protection 15
- Recycling 15
- Regulatory Compliances 16
- Patent Notice 18
- Trademarks 18
- License Agreement 18
- Warranty 18
- PRODUCT OVERVIEW 19
- Pressure Measurement 20
- Structure of the Transmitter 22
- 0604-060 23
- 0911-067 25
- INSTALLATION 27
- 0503-004 28
- 0804-065 28
- 0503-002 30
- 0503-041 32
- 0509-151 32
- 0704-002 34
- 0804-083 34
- Grounding the Cables 36
- Alternate Wiring Systems 37
- WARNING 38
- 8-Pin Connector 39
- D-9 Connector 40
- CAUTION 41
- Probe Mounting 42
- 0507-024 43
- 0507-022 43
- Temperature Probe (Optional) 45
- Optional Modules 46
- Installation 47
- Warnings 48
- Third Analog Output 51
- Installation and Wiring 52
- RS-422/485 Interface 55
- Figure 33 4-Wire RS-485 Bus 57
- LAN Interface 58
- WLAN Interface 59
- Data Logger Module 60
- 0706-068 62
- Reading 64
- 0604-055 65
- Graphic History 67
- Information Display 68
- Menus and Navigation 69
- Changing the Language 70
- Rounding Setting 71
- Display Backlight Setting 71
- Display Contrast Setting 71
- Keypad Lock (Keyguard) 71
- Menu PIN Lock 72
- Factory Settings 72
- Display Alarms 73
- 0802-069 74
- 0802-070 74
- User Port Connection 76
- Service Port Connection 77
- Using the Service Port 78
- LAN Communication 79
- Wireless LAN Configuration 83
- Telnet Settings 85
- 0802-114 86
- 0810-071 88
- Serial Line 91
- Outputting Reading Once 92
- General Settings 94
- Date and Time 97
- N_#r #n 99
- GPS Commands 100
- Using Display/Keypad 101
- Using Serial Line 102
- User Port Serial Settings 104
- Pressure Average Calculation 107
- Device Information 108
- Data Recording 111
- View Recorded Data 112
- Analog Output Settings 115
- 0503-045 116
- AMODE/ASEL 118
- Analog Output Tests 119
- Operation of Relays 121
- Hysteresis 122
- 0610-077 123
- Testing Operation Of Relays 126
- Networking Commands 128
- Sensor Functions 131
- Manual Chemical Purge 132
- Chemical Purge in Power Up 133
- Using Buttons On Motherboard 133
- Setting Sensor Heating 135
- Display/Keypad 136
- MAINTENANCE 137
- Changing the Sensor 138
- Error States 139
- Table 33 Error Messages 140
- Technical Support 141
- Return Instructions 141
- Vaisala Service Centers 142
- CALIBRATION AND ADJUSTMENT 143
- 0508-013 144
- Relative Humidity Adjustment 148
- Temperature Adjustment 152
- TECHNICAL DATA 157
- Relative Humidity 158
- Optional Temperature Probe 159
- Calculated Variables 160
- 1013 mbar) 161
- Probe Option) 162
- Inputs and Outputs 163
- Mechanics 163
- Modules 164
- Relay Module 165
- RS-485 Module 165
- LAN Interface Module 165
- WLAN Interface Module 165
- Options and Accessories 166
- Dimensions (mm/inch) 168
- 0804-033 169
- 12 (0.47) 170
- 120 (4.72) 170
- Temperature Probe 171
- PROBE INSTALLATION KITS AND 173
- INSTALLATION EXAMPLES 173
- PTU307) 174
- 0508-016 176
- 0508-018 178
- 0508-015 178
- 0601-044 180
- 99.621 182
Související produkty a manuály pro Měření, testování a kontrola Vaisala PTU300
(84 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce