Vaisala HUMICAP HMT330 SERIES Uživatelská příručka Strana 137
- Strana / 178
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6 ___________________________________________________Calibration and Adjustment
VAISALA ______________________________________________________________________ 137
CHAPTER 6
CALIBRATION AND ADJUSTMENT
The HMT330 is fully calibrated and adjusted as shipped from factory.
Typical calibration interval is one year. Depending on the application it
may be good to make more frequent checks. Calibration must be done
always when there is a reason to believe that the device is not within the
accuracy specifications.
It is recommended that calibration and adjustment should be carried out
by Vaisala. See section Vaisala Service Centers on page 136.
Calibration and adjustment is carried out either by using the push-keys on
the motherboard, through the serial port or with the optional
display/keypad.
(Vaisala portable instruments HM70 and HMI41 can also be used).
Opening and Closing the Adjustment Mode
1. Open the transmitter cover. The buttons needed in adjustment are
on the left-hand side of the motherboard.
2. If the chemical purge option is available, it should be carried out
always before calibration. To start chemical purge press
simultaneously two PURGE push-keys (on the motherboard) for a
few seconds. Red indicator led flashes with short pulses until purge
is complete (up to 6 minutes).
3. Press the ADJ key to open the adjustment mode.
4. Press the ADJ key again to close the adjustment mode.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 5 6
- CHAPTER 6 7
- CHAPTER 7 7
- APPENDIX A 8
- APPENDIX B 8
- List of Figures 9
- GENERAL INFORMATION 13
- Version Information 14
- Feedback 15
- ESD Protection 15
- Recycling 16
- Regulatory Compliances 16
- Patent Notice 18
- Trademarks 18
- License Agreement 18
- Warranty 18
- PRODUCT OVERVIEW 19
- Basic Features and Options 20
- Structure of the Transmitter 21
- 0508-010 22
- 0911-066 24
- INSTALLATION 27
- 0503-004 28
- 0804-065 28
- Pole or Pipeline 30
- 0503-007 31
- 0503-041 31
- Panel Mounting Frame 33
- Cable Bushings 34
- Grounding the Cables 35
- WARNING 37
- CAUTION 38
- 0703-041 39
- Probe Mounting 40
- 0507-024 41
- Applications 43
- 0506-029 44
- 0503-034 44
- Temperature Probe (Optional) 46
- 0507-025 47
- 0508-077 47
- Optional Modules 49
- Installation 50
- Warnings 50
- Third Analog Output 53
- Installation and Wiring 54
- RS-422/485 Interface 57
- 1 (not connected) RxB 58
- 2 (not connected) RxA 58
- 4 B TxB 58
- 5 A TxA 58
- LAN Interface 59
- WLAN Interface 60
- Attaching the WLAN Antenna 61
- Data Logger Module 62
- 0706-068 63
- OPERATION 65
- Graphic History 66
- 0706-030 67
- Changing the Language 69
- Rounding Setting 69
- Display Backlight Setting 69
- Display Contrast Setting 70
- Keypad Lock (Key guard) 70
- Menu PIN Lock 70
- Display Alarms 71
- Configuring a Display Alarm 72
- Serial Line Communication 73
- RS-232 10…36 V= 74
- Service Port Connection 75
- Using the Service Port 76
- LAN Communication 77
- Wireless LAN Configuration 80
- 0802-111 81
- 0802-110 81
- 0802-112 81
- Telnet Settings 83
- Terminal Program Settings 84
- 0810-070 85
- List of Serial Commands 87
- Serial Line 89
- Outputting Reading Once 90
- FTIME and FDATE 91
- General Settings 92
- Example: 94
- Date and Time 97
- User Port Serial Settings 98
- Data Filtering 101
- Device Information 101
- 0706-002 102
- Data Recording 104
- View Recorded Data 105
- Analog Output Settings 108
- 0503-045 109
- Analog Output Quantities 110
- AMODE/ASEL 111
- Analog Output Tests 112
- Operation of Relays 114
- Hysteresis 115
- Enabling/Disabling Relays 116
- Setting Relay Outputs 117
- Testing Operation of Relays 119
- Networking Commands 120
- Sensor Functions 124
- Manual Chemical Purge 125
- Chemical Purge in Power Up 125
- Using Buttons on Motherboard 126
- Using Serial Line 127
- Sensor Heating 128
- MAINTENANCE 131
- Changing the Sensor 132
- Error States 133
- Table 29 Error Messages 134
- Technical Support 135
- Return Instructions 135
- Vaisala Service Centers 136
- CALIBRATION AND ADJUSTMENT 137
- 0508-013 138
- 0706-007 138
- Using Display/Keypad 140
- Temperature Adjustment 143
- Analog Output Adjustment 145
- TECHNICAL DATA 147
- Optional Temperature Probe 148
- Calculated Variables 149
- 1013 mbar) 149
- Probe Option) 151
- Operating Environment 151
- Inputs and Outputs 152
- Mechanics 152
- Modules 153
- Relay Module 154
- RS-485 Module 154
- LAN Interface Module 154
- WLAN Interface Module 154
- Options and Accessories 155
- Dimensions (mm/inch) 157
- 0804-035 158
- 0804-060 160
- 0804-059 160
- Temperature Probe 162
- PROBE INSTALLATION KITS AND 163
- INSTALLATION EXAMPLES 163
- HMT337) 164
- Cable Gland 166
- 0508-015 167
- 0508-022 167
- 0507-015 169
- 0507-043 170
- 0804-063 172
Související produkty a manuály pro Měření, testování a kontrola Vaisala HUMICAP HMT330 SERIES
(22 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce